reversed-phase raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2025-05-12 and is reviewed periodically as new material appears.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
| Property | Value | Notes |
|---|---|---|
| Common abbreviation | HPLC | High-performance liquid chromatography |
| Separation basis | Differential partitioning | Between liquid mobile phase and solid stationary phase |
| Common mode | Reverse phase | Nonpolar column, polar mobile phase |
| Typical detector | UV-Vis absorbance | Widely used for compounds with chromophores |
| Typical column particle size | 2–5 µm | Smaller particles can improve resolution |
Regulatory and pharmacopeial texts shape how HPLC testing is performed and documented. The International Council for Harmonisation provides validation guidance, while pharmacopeias publish general chromatography chapters and monographs for specific materials. Accreditation standards such as ISO/IEC 17025 address laboratory competence and traceability. Inspectors may review instrument qualification, analyst training, reference material control, and electronic records. Open questions include how best to validate methods for new complex products and how to handle automated data processing. Laboratories generally resolve these issues through risk assessment, method lifecycle management, and documented scientific justification.
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
AOD9604 is an orally active, lipolytic 16-amino acid peptide fragment of human growth hormone and derivative of the C-terminal domain of human growth hormone (HGH). It consists of HGH residues 176–191, with a tyrosine in place of the phenylalanine at the N-terminal end. Initial human trials showed that it retains the lipolytic properties of human growth hormone without stimulating IGF-1 production. However, later studies failed to demonstrate a sufficient lipolytic effect. Its development was terminated in 2007. Despite its limited efficacy, AOD9604 is still banned in athletes and tested for in competition. AOD9604 appears to enhance lipolysis in mice by upregulating beta-3 adrenergic receptors. Beta-3 adrenergic receptor knockout mice are unresponsive to the lipolytic effects of AOD9604. In a 12 week randomised clinical trial, subjects receiving AOD9604 lost, on average, 1.8 kg more than those receiving placebo. Development of AOD9604 was halted following poor efficacy in a later 24 week trial.
Actovegin is a highly filtered extract obtained from calf blood which enhances aerobic oxidation in mammals. This improves absorption of glucose and oxygen uptake in tissue, which may enhance physical performance and stamina. Local utilisation is allowed in countries like Canada and Sweden. Doctors like Hans-Wilhelm Müller-Wohlfahrt and Richard Steadman think Actovegin should be allowed in general. Others think there is not enough research, and persons from the World Anti-Doping Agency like Olivier Rabin is sceptical that it is having more than a placebo effect. Actovegin made headlines from 2009 to 2011 when Canadian sports doctor Anthony Galea was charged with drug smuggling, conspiring to lie to federal agents, unlawful possession with intent to distribute and practising medicine without a licence in the United States. Galea pleaded guilty of bringing misbranded and unapproved drugs, including Nutropin, a human growth hormone, and Actovegin, into the United States. The discipline committee for the College of Physicians and Surgeons of Ontario (CPSO) suspended Galeas license for 9 months for professional misconduct.
ALK-positive ALCL occurs mostly but not exclusively in children and young adults and is slightly more common in males. Most individuals present with stage III or IV (i.e. advanced) disease. They evidence systemic symptoms including B symptoms such as fever, night sweats, and weight loss in 75% of cases; lymph node enlargement (90%) including those in the mediastinum (36%); and lymphomatous lesions in the skin (26%), bone (14%), soft tissues (15%), lung (12%), and/or liver (8%). Tumor cells are found in the bone marrow in up to 40% of the cases when immunohistochemical analysis is performed. Involvement of the central nervous system or a leukemia-like circulation of malignant cells in the blood occurs only very rarely. Most patients, including up to 90% of young children and adolescents, have circulating autoantibodies directed against the ALK fusion protein expressed by their tumor cells.
Environmental health laboratories are governmental laboratories that conduct testing to protect human health and the environment. In some states, a single laboratory acts as both the environmental and the public health laboratory. In other states, the environmental laboratory is part of the department of environmental quality or natural resources while the public health laboratory is part of the health department. Environmental health laboratories help to identify contaminants by conducting regular testing of water, air, soil, food and other media to ensure that populations are not being exposed to unhealthy levels of contamination. APHL supports these laboratories by coordinating a response to environmental health issues. They assist in providing information and training to the scientists working in the labs, and serve as a link between member laboratories and federal agencies, including Centers for Disease Control and Prevention's (CDC) National Center for Environmental Health and the US Environmental Protection Agency.
Sources: en.wikipedia.org
Following TNF-R1 and Fas activation in mammalian cells a balance between proapoptotic (BAX, BID, BAK, or BAD) and anti-apoptotic (Bcl-Xl and Bcl-2) members of the Bcl-2 family are established. This balance is the proportion of proapoptotic homodimers that form in the outer-membrane of the mitochondrion. The proapoptotic homodimers are required to make the mitochondrial membrane permeable for the release of caspase activators such as cytochrome c and SMAC. Control of proapoptotic proteins under normal cell conditions of nonapoptotic cells is incompletely understood, but in general, Bax or Bak are activated by the activation of BH3-only proteins, part of the Bcl-2 family.
Arrestins are elongated molecules, in which several intra-molecular interactions hold the relative orientation of the two domains. Unstimulated cell arrestins are localized in the cytoplasm in a basal inactive conformation. Active phosphorylated GPCRs recruit arrestin to the plasma membrane. Receptor binding induces a global conformational change that involves the movement of the two arrestin domains and the release of its C-terminal tail that contains clathrin and AP2 binding sites. Increased accessibility of these sites in receptor-bound arrestin targets the arrestin-receptor complex to the coated pit. Arrestins also bind microtubules (part of the cellular skeleton), where they assume yet another conformation, different from both free and receptor-bound form. Microtubule-bound arrestins recruit certain proteins to the cytoskeleton, which affects their activity and/or redirects it to microtubule-associated proteins. Arrestins shuttle between cell nucleus and cytoplasm. Their nuclear functions are not fully understood, but it was shown that all four mammalian arrestin subtypes remove some of their partners, such as protein kinase JNK3 or the ubiquitin ligase Mdm2, from the nucleus. Arrestins also modify gene expression by enhancing transcription of certain genes.
GABA-T is Enzyme Commission number 2.6.1.19. This means that it is in the transferase class of enzymes, the nitrogenous transferase sub-class and the transaminase sub-subclass. As a nitrogenous transferase, its role is to transfer nitrogenous groups from one molecule to another. As a transaminase, GABA-T's role is to move functional groups from an amino acid and a α-keto acid, and vice versa. In the case of GABA-T, it takes a nitrogen group from GABA and uses it to create L-glutamate. In animals, fungi, and bacteria, GABA-T helps facilitate a reaction that moves an amine group from GABA to α-ketoglutaric acid, and a ketone group from α-ketoglutaric acid to GABA. This produces succinate semialdehyde and L-glutamic acid. In plants, pyruvic acid and glyoxylic acid can be used in the place of α-ketoglutaric acid, catalyzed by the enzyme 4-aminobutyrate—pyruvate transaminase:
Elimination of protruding knobs and controls in passenger compartment Additional padding on the instrument panel and other interior surfaces Mounting points for front outboard shoulder belts Four-way hazard flashers A uniform P-R-N-D-L gear sequence for automatic transmission gear selectors Dual-circuit brake hydraulic systems In 1968, the precursor agency to the US National Highway Traffic Safety Administration's first Federal Motor Vehicle Safety Standards took effect. These required shoulder belts for left and right front-seat vehicle occupants, side marker lights, collapsible steering columns, and other safety features. 1969 saw the addition of head restraints for front outboard passengers, addressing the problem of whiplash in rear-end collisions. These safety requirements did not apply to vehicles classified as "commercial," such as light-duty pickup trucks. Thus, manufacturers did not always include such hardware in these vehicles, even though many did passenger-car duty. Volvo developed the first rear-facing child seat in 1964 and introduced its own booster seat in 1978.
Clear Lake Audiotorium is a six-track promo EP by De La Soul given out to A-list DJs in 1994, the catalog number is TB 1093 (Side A, "THIS SIDE" is TB 1093 A and Side B "OTHER SIDE" is TB 1093 B). It was composed of four tracks from the group's album Buhloone Mindstate and two non-album tracks—"Sh.Fe.Mc's" featuring A Tribe Called Quest, and "Stix & Stonz" featuring The Fearless Four, Grandmaster Caz, and Prince Whipper Whip. With only 500 copies pressed (vinyl and CD), Clear Lake Audiotorium remains one of the most sought-after De La Soul releases to date. Originally pressed on clear/light green vinyl and packaged in a clear plastic sleeve, the record has since been bootlegged on black vinyl. On March 7, 2025, exactly 31 years after its original release, the EP was released officially on streaming releases, alongside a limited physical re-release.
Sources: en.wikipedia.org
Pseudoacromegaly is a condition with the usual acromegaloid features but without an increase in growth hormone and IGF-1. It is frequently associated with insulin resistance. Cases have been reported due to minoxidil at an unusually high dose. It can also be caused by a selective post-receptor defect of insulin signalling, leading to the impairment of metabolic, but preservation of mitogenic, signaling. Treatment options include surgery to remove the tumor, medications, and radiation therapy. Surgery is usually the preferred treatment; the smaller the tumor, the more likely surgery will be curative. If surgery is contraindicated or not curative, somatostatin analogues or GH receptor antagonists may be used. Radiation therapy may be used if neither surgery nor medications are completely effective. Without treatment, life expectancy is reduced by 10 years; with treatment, life expectancy is not reduced.
In the most common means for its production, cells make 5-oxo-ETE in a four step pathway that involves their stimulus-induced activation of the following pathway: a) the release of arachidonic acid (i.e. 5Z,8Z,11Z,14Z-eicosatetraenoic acid) from its storage sites in membrane phospholipids due to the activation of phospholipase A2 enzymes; b) oxygenation of this arachidonic acid by activated arachidonate 5-lipoxygenase (ALOX5) to form 5(S)-hydroperoxy-6E,8Z,11Z,14Z-eicosatetraenoic acid (5(S)-HpETE); c) reduction of this 5(S)-HpETE by ubiquitous cellular peroxidases to form 5(S)-hydroxy-6E,8Z,11Z,14Z-eicosatetraenoic acid (5(S)-HETE); and (d) the oxidation of 5(S)-HETE by a microsome-bound nicotinamide adenine dinucleotide phosphate (NADP+)-dependent dehydrogenase enzyme viz., 5-hydroxyeicosanoid dehydrogenase (5-HEDH), to form 5-oxo-ETE:
Hydrogen halides and their solutions: hydrofluoric acid (HF), hydrochloric acid (HCl), hydrobromic acid (HBr), hydroiodic acid (HI) Halogen oxoacids: hypochlorous acid (HClO), chlorous acid (HClO2), chloric acid (HClO3), perchloric acid (HClO4), and corresponding analogs for bromine and iodine Hypofluorous acid (HFO), the only known oxoacid for fluorine. Sulfuric acid (H2SO4) Fluorosulfuric acid (HSO3F) Nitric acid (HNO3) Phosphoric acid (H3PO4) Fluoroantimonic acid (HSbF6) Fluoroboric acid (HBF4) Hexafluorophosphoric acid (HPF6) Chromic acid (H2CrO4) Boric acid (H3BO3) A sulfonic acid has the general formula RS(=O)2–OH, where R is an organic radical. Methanesulfonic acid (or mesylic acid, CH3SO3H) Ethanesulfonic acid (or esylic acid, CH3CH2SO3H) Benzenesulfonic acid (or besylic acid, C6H5SO3H) p-Toluenesulfonic acid (or tosylic acid, CH3C6H4SO3H) Trifluoromethanesulfonic acid (or triflic acid, CF3SO3H) Polystyrene sulfonic acid (sulfonated polystyrene, [CH2CH(C6H4)SO3H]n)
Across several benchmarks, AlphaFold3 has demonstrated, on average, superior performance to conventional search-based docking algorithms in predicting small-molecule–protein binding modes. AlphaFold 3 version can predict structures of protein complexes with a very limited set of selected cofactors and co- and post-translational modifications. Between 50% and 70% of the structures of the human proteome are incomplete without covalently-attached glycans. Studies have shown that although AlphaFold3 can jointly model protein–ligand co-folding, its accuracy drops markedly on test cases with low similarity to its training data—an area of particular importance for drug discovery. Other work has found that AlphaFold is insensitive to adversarial decoys generated by altering the physicochemical properties of binding pockets, suggesting potential reliance on training-set memorization rather than genuine chemical awareness.
Clinical trial number NCT02609776 for "Study of Amivantamab, a Human Bispecific EGFR and cMet Antibody, in Participants With Advanced Non-Small Cell Lung Cancer (CHRYSALIS)" at ClinicalTrials.gov Clinical trial number NCT04487080 for "A Study of Amivantamab and Lazertinib Combination Therapy Versus Osimertinib in Locally Advanced or Metastatic Non-Small Cell Lung Cancer (MARIPOSA)" at ClinicalTrials.gov Clinical trial number NCT04988295 for "A Study of Amivantamab and Lazertinib in Combination With Platinum-Based Chemotherapy Compared With Platinum-Based Chemotherapy in Patients With Epidermal Growth Factor Receptor (EGFR)-Mutated Locally Advanced or Metastatic Non- Small Cell Lung Cancer After Osimertinib Failure (MARIPOSA-2)" at ClinicalTrials.gov Clinical trial number NCT04538664 for "A Study of Combination Amivantamab and Carboplatin-Pemetrexed Therapy, Compared With Carboplatin-Pemetrexed, in Participants With Advanced or Metastatic Non-Small Cell Lung Cancer Characterized by Epidermal Growth Factor Receptor (EGFR) Exon 20 Insertions (PAPILLON)" at ClinicalTrials.gov
Sources: en.wikipedia.org
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.
Retention time is the interval between sample injection and the detector response for a given compound. It depends on the compound's interactions with the stationary and mobile phases under set conditions. Matching a retention time to a standard supports tentative identification but is not always unique.
HPLC alone can separate unknown compounds and provide retention times, but it often cannot identify them with certainty. Coupling HPLC to mass spectrometry gives mass information that improves identification. Confirmation usually requires comparison with reference standards or complementary techniques.
HPLC separates and quantifies compounds in a liquid sample. Detectors produce a response proportional to the amount of a compound passing through the flow cell. Identification by retention time requires comparison with a known standard.