A practical reference on System suitability: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
This page was last updated on 2025-03-23 and is reviewed periodically as new material appears.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness of measured value to accepted reference value |
| Validation parameter | Precision | Agreement among repeated measurements under specified conditions |
| System suitability check | Resolution ≥ 1.5 | Baseline separation between critical peak pair |
| System suitability check | Tailing factor ≤ 2.0 | Common target for peak symmetry |
| Documentation | Validation report | Summarizes experiments, acceptance criteria, and conclusions |
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
The Society recognizes achievements and promotes academic research through four annual awards. The Biemann Medal and the John B. Fenn Award for a Distinguished Contribution in Mass Spectrometry both are awarded in recognition of singular achievements or contributions in fundamental or applied mass spectrometry, with the Biemann Medal being focused on individuals who are early in their careers. The Ronald A. Hites Award is awarded for outstanding original research demonstrated in papers published in the Journal of the American Society for Mass Spectrometry. The Research Awards are given to young scientists in mass spectrometry, based on the evaluation of their proposed research. The Fellows of ASMS are awarded to individuals in recognition for their scientific contribution to mass spectrometry and for their contribution to the ASMS community. Journal of the American Society for Mass Spectrometry Measuring Mass: From Positive Rays to Proteins The past presidents of ASMS are:
Viscous mucus secreted by glands in the cervix presents a unique environment for drug delivery. Due to its ability to retain substances and slowly release them, it holds potential to be used as a natural, noninvasive drug delivery system. The mucus can act as a reservoir for compounds that destroy pathogens. However, the cervical mucus also presents a barrier to drug delivery as it can be really thick, making it difficult to permeate the mucus barrier. The mechanisms for penetration and bioactivity of the cervical mucus must be understood to utilize the mucus’s potential as a drug delivery system. Due to the changes in viscosity and water content of the mucus during the stages of the menstrual cycle, this poses a particularly complex consideration. For example, the cervical mucus will be thicker when a woman is not ovulating in order to prevent sperm from being able to penetrate the mucus barrier, which also in turn makes in more difficult for penetration of drug delivery systems.
Non-specific active immunotherapy: generating a general immune system response using cytokines and other cell signaling molecules. Specific active immunotherapy: the generation of cell-mediated and antibody immune responses focused on specific antigens expressed by the cancer cells, typically using a vaccine platform. Active immunotherapies fall under the category of activation immunotherapies, which is a subset of immunotherapies that activate the immune system as opposed immunotherapies that suppress the immune system. Non-specific active immunotherapy is administered with the overall goal of generally eliminating malignant pathogens or cells from the host system. This treatment stimulates the immune system in a general sense, rather than specifically targeting a cell type e.g. cancer cells. Non-specific approaches aim to create a robust immune response that would lead to the eventual killing of malignant cells through immunomodulators such as cytokines.
While the initial consolidation of Air Force laboratories reduced overhead and budgetary pressure, another push towards a unified laboratory structure came in the form of the National Defense Authorization Act for Fiscal Year 1996, Section 277. This section instructed the Department of Defense to produce a five-year plan for consolidation and restructuring of all defense laboratories. The currently existing laboratory structure was created in October 1997 through the consolidation of Phillips Laboratory headquartered in Albuquerque, New Mexico, Wright Laboratory in Dayton, Ohio, Rome Laboratory (formerly Rome Air Development Center) in Rome, New York, and Armstrong Laboratory in San Antonio, Texas and the Air Force Office of Scientific Research (AFOSR). The single laboratory concept was developed and championed by Maj Gen Richard Paul, who was Director of Science & Technology for AFMC and Gen Henry Viccellio Jr, and then became the first Commander of AFRL.
Sources: en.wikipedia.org
5-HT2C receptor agonists reduce appetite by working on serotonin receptors in a region of the brain called the hypothalamus. Lorcaserin (Belviq) was FDA approved for weight loss but was withdrawn from the market because a safety clinical trial shows an increased occurrence of cancer. Cannabinoid receptor antagonists were developed to treat obesity because researchers noticed that cannabinoid agonists (such as THC, the main pharmacologically active component of cannabis), increased appetite. However, some drugs in this class such as rimonabant were withdrawn or ceased development due to concerns about mental health and suicide. More selective drugs—some are in development that act only in peripheral tissues, not the brain—may be able to achieve this result with fewer adverse effects. GLP-1 agonists such as tirzepatide, semaglutide, and liraglutide slow gastric emptying and also have neurologically driven effects on appetite. It is unknown if GLP-1 agonists or dual/triple agonists of GLP-1 and/or the glucagon or GIP receptors act solely by reducing energy intake or if they also increase energy expenditure. Setmelanotide is an agonist of the melanocortin 4 receptor and is used in people with certain rare genetic conditions that cause obesity. It is less effective and not approved for general obesity.
Aldo Carl Leopold (December 18, 1919 – November 18, 2009) was an American academic and plant physiologist, son of Aldo Leopold, a noted ecologist. He is known for his research on soybeans which led to techniques allowing insulin to be dried and later processed into an inhalable insulin. Aldo Carl Leopold was born to Aldo Leopold, a noted ecologist and employee of the United States Forest Service, and Estella Leopold in Albuquerque, New Mexico as the 4th of 5 children.
Newton has been a major driver in the PKC research field since the 1980s, working originally with Daniel E. Koshland Jr. She helped define the multiple different mechanisms of PKC regulation by phosphorylation and its interaction with specific membrane phospholipids, such as phosphatidylserine She has also made important discoveries in the protein phosphatase field, discovering and naming PHLPP (PH domain and Leucine rich repeat Protein Phosphatases), which regulate intracellular signaling through dephosphorylation of AKT. As of 2020, Newton has published over 190 peer-reviewed research articles that have been cited more than 25,000 times, been awarded 1 patent and co-edited two books on protein biochemistry and PKC. Her work straddles basic research and has illuminated understanding of PKC in Alzheimer's disease and as a tumor suppressor in human cancers
Sources: en.wikipedia.org
Adiponectin (also referred to as GBP-28, apM1, AdipoQ and Acrp30) is a protein hormone and adipokine, which is involved in regulating glucose levels and fatty acid breakdown. In humans, it is encoded by the ADIPOQ gene and is produced primarily in adipose tissue, but also in muscle and even in the brain. Adiponectin is a 244-amino-acid-long polypeptide (protein). It has four distinct regions: The first is a short signal sequence that targets the hormone for secretion outside the cell; next is a short region that varies between species; the third is a 65-amino acid region with similarity to collagenous proteins; the last is a globular domain. Overall, this protein shows similarity to the complement 1Q factors (C1Q), but when the three-dimensional structure of the globular region was determined, a striking similarity to TNFα was observed, despite unrelated protein sequences.
Živojinović (nicknamed Bata) was born in the village of Koraćica under the Kosmaj mountain near Mladenovac, at the time Kingdom of Yugoslavia (now Serbia). His father, Dragoljub, was an official and his mother Tiosava was a housewife. He had two sisters, Stanka and Nada, and grew up in a patriarchal household. A conflict between Dragoljub and the Chetniks during World War II forced the family to move to Belgrade. The family lived in Crveni Krst. Young Bata often went with his friends to the cinema, which sparked his interest in acting. Loitering around the "20th October" cinema, he watched AKUD Branko Krsmanović, a Belgrade troupe, through the window for several days until he was welcomed inside. There he befriended Soja Jovanović, instrumental in the developing of Bata's love for acting, Rade Marković, Olivera Marković, Mića Tomić, and Bata Paskaljević. After graduating from acting schools in Niš and Novi Sad, he enrolled at the Drama Academy in Belgrade.
Both the thyroid and adrenal glands can be infiltrated. It is estimated that 10–20% of people with amyloidosis have hypothyroidism. Adrenal infiltration may be harder to appreciate given that its symptoms of orthostatic hypotension and low blood sodium concentration may be attributed to autonomic neuropathy and heart failure. "Amyloid deposits occur in the pancreas of people who also have diabetes mellitus, although it is not known if this is functionally important. The major component of pancreatic amyloid is a 37-amino acid residue peptide known as islet amyloid polypeptide or 'amylin.' This is stored with insulin in secretory granules in [beta] cells and is co secreted with insulin." (Rang and Dale's Pharmacology, 2015.)
The most common application of cervical drug delivery is for treatment of cervical cancer. Due to the direct route provided through the use of cervical drug delivery mechanisms, it proves to be the most effective route with the lowest number of side effects. The localized treatment has been suggested as ideal as cancer is treated with highly toxic compounds, such as chemotherapeutics. The more contained the exposure to these compounds can be, the less negative impacts the patient will endure. Treatment can be delivered in the form of nanoparticles, vaginal gels, or films and reach the cervix quickly for ideal response. Vaginal gels are easily administered into the vaginal canal to reach the cervix due to low viscosity at room temperature. When inserted into the body which has a higher temperature, the gels become more viscous, allowing them to reside longer at the cervix and have more sustained release. Vaginal films are very thin films inserted into the vagina to release a compound. They can be maintained for six hours in cervical mucus, meaning they hold potential to treat cervical cancer caused by Human Papilloma Virus. Nanoparticle systems take advantage of the size of nanoparticles to encapsulate the drugs and pass through the mucus barrier.
Sources: en.wikipedia.org
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.
Validation follows a planned protocol that tests accuracy, precision, specificity, linearity, range, detection limits, quantitation limits, and robustness. Results are compared against predefined acceptance criteria. The validation report supports regulatory filing or routine use.
Revalidation may be needed after changes to column chemistry, mobile phase, detection, sample preparation, or instrument type. It can also follow a pattern of out-of-specification results. The scope depends on whether the change affects method performance.
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.