The short version of quality control fits in a sentence. The long version — which is the one that helps — is below.
Reviewed 2026-03-12. Anything still debated is marked as such rather than presented as settled.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
| Parameter | Typical acceptance criterion | Notes |
|---|---|---|
| Resolution | ≥ 1.5 | Baseline separation of adjacent peaks |
| Tailing factor | ≤ 2.0 | Peak symmetry measure |
| Theoretical plates | > 2000 | Column efficiency indicator |
| Injection repeatability | ≤ 2% RSD | Relative standard deviation for replicate injections |
| Linearity | r² ≥ 0.995 | Calibration curve over the working range |
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Brenipatide (INNTooltip International Nonproprietary Name, USANTooltip United States Adopted Name; developmental code name LY-3537031) is a dual agonist of glucagon-like peptide-1 (GLP-1) receptors and gastric inhibitory polypeptide (GIP) receptors. Brenipatide is under development by Eli Lilly and Company for the treatment of alcoholism, bipolar disorder, asthma, smoking withdrawal, cardiovascular disorders, liver disorders, metabolic disorders, and obesity. It is taken by subcutaneous injection once per month. The drug has a longer elimination half-life than tirzepatide or retatrutide. As of December 2025, it was in phase 3 clinical trials for alcoholism and bipolar disorder, phase 2 trials for asthma and smoking withdrawal, and phase 1 trials for cardiovascular disorders, liver disorders, metabolic disorders, and obesity. List of investigational antipsychotics List of investigational bipolar disorder drugs List of investigational substance-related disorder drugs
Abdominal obesity is typically associated with a statistically higher risk of heart disease, hypertension, insulin resistance, and type 2 diabetes (see below). With an increase in the waist to hip ratio and overall waist circumference the risk of death increases as well. Metabolic syndrome is associated with abdominal obesity, blood lipid disorders, inflammation, insulin resistance, type 2 diabetes, and an increased risk of developing cardiovascular disease. It is now generally believed that intra-abdominal fat is the depot that conveys the biggest health risk. Recent validation has concluded that total and regional body volume estimates correlate positively and significantly with biomarkers of cardiovascular risk and that BVI calculations correlate significantly with all biomarkers of cardiovascular risk. Abdominal obesity is linked with higher cardiovascular events among South Asian ethnic populations.
The permeability of a membrane is the rate of passive diffusion of molecules through the membrane. These molecules are known as permeant molecules. Permeability depends mainly on the electric charge and polarity of the molecule and to a lesser extent the molar mass of the molecule. Due to the cell membrane's hydrophobic nature, small electrically neutral molecules pass through the membrane more easily than charged, large ones. The inability of charged molecules to pass through the cell membrane results in pH partition of substances throughout the fluid compartments of the body. Lipids, Membranes and Vesicle Trafficking – The Virtual Library of Biochemistry and Cell Biology Cell membrane protein extraction protocol Membrane homeostasis, tension regulation, mechanosensitive membrane exchange and membrane traffic 3D structures of proteins associated with plasma membrane of eukaryotic cells Lipid composition and proteins of some eukariotic membranes Prokaryotic and Eukaryotic Cells
Berg did not complete his final step due to the pleas of several fellow investigators, including Robert Pollack, who feared the biohazards associated with the last step. The SV40 was known to cause cancer tumors to develop in mice. Additionally, the E. coli bacterium (although not the strain used by Berg) inhabited the human intestinal tract. For these reasons, the other investigators feared that the final step would create cloned SV40 DNA that might escape into the environment and infect laboratory workers. These workers could then become cancer victims. Concern about this potential biohazard, along with others, caused a group of leading researchers to send a letter to the president of the National Academy of Sciences (NAS). In this letter, they requested that he appoint an ad hoc committee to study the bio-safety ramifications of this new technology. This committee, called the Committee on Recombinant DNA molecules of the National Academy of Science, U.S.A., held in 1974, concluded that an international conference was necessary to resolve the issue and that until that time, scientists should halt experiments involving recombinant DNA technology.
Sources: en.wikipedia.org
In the UK, a House of Commons Select Committee on Environment, Food and Rural Affairs report on the horse meat incident was not critical of UK or Irish producers. It expressed concern that horsemeat contamination resulted from fraud and other criminal activity across the EU. Chair of the Committee, Anne McIntosh MP, said: "The evidence suggests a complex network of companies trading in and mislabelling beef or beef products which is fraudulent and illegal." The second major UK report on the horse meat incident was conducted by Professor Chris Elliott, the Director of the Institute for Global Food Security at Queen's University Belfast. In his independent report, he argues that food crime was at the heart of the horsemeat incident and makes a range of suggestions for how this could be tackled. "Industry, government and enforcement agencies should, as a precautionary principle, always put the needs of consumers above all other considerations, and this means giving food safety and food crime prevention—i.e. the deterrence of dishonest behaviour—absolute priority over other objectives."
During the 2015 high school football season, Kuper was an offensive line coach at Columbine High School in Littleton, Colorado. On January 23, 2016, Kuper was hired by Miami Dolphins as offensive quality control coach. He then spent two seasons (2017–18) as the assistant offensive line coach for Miami. On January 22, 2019, the Denver Broncos hired Kuper as their assistant offensive line coach. With the firing of Vic Fangio from the Broncos, Kuper was hired by Kevin O'Connell to be the offensive line coach for the Minnesota Vikings. Before the 2026 season, his contract expired and the Vikings chose not to retain him. On February 9, 2026, the Philadelphia Eagles hired Kuper as their new offensive line coach. Eagles offensive coordinator Sean Mannion previously played for the Minnesota Vikings at the end of his playing career, during which Kuper served as the Vikings offensive line coach. UND Football bio Denver Broncos bio Kuper not letting broken right hand block opportunity
Ectopic fat is the storage of triglycerides in tissues other than adipose tissue, that are supposed to contain only small amounts of fat, such as the liver, skeletal muscle, heart, and pancreas. This can interfere with cellular functions and hence organ function and is associated with insulin resistance in type 2 diabetes. It is stored in relatively high amounts around the organs of the abdominal cavity, but is not to be confused with visceral fat. The specific cause for the accumulation of ectopic fat is unknown. The cause is likely a combination of genetic, environmental, and behavioral factors that are involved in excess energy intake and decreased physical activity. Substantial weight loss can reduce ectopic fat stores in all organs and this is associated with an improvement of the function of those organs. In the latter case, non-invasive weight loss interventions like diet or exercise can decrease ectopic fat (particularly in heart and liver) in overweight or obese children and adults.
Sources: en.wikipedia.org
TNF is a cytokine produced mainly by activated macrophages, and is the major extrinsic mediator of apoptosis. Most cells in the human body have two receptors for TNF: TNFR1 and TNFR2. The binding of TNF to TNFR1 has been shown to initiate the pathway that leads to caspase activation via the intermediate membrane proteins TNF receptor-associated death domain (TRADD) and Fas-associated death domain protein (FADD). cIAP1/2 can inhibit TNF signaling by binding to TRAF2. FLIP inhibits the activation of caspase-8. Binding of this receptor can also indirectly lead to the activation of transcription factors involved in cell survival and inflammatory responses. However, signalling through TNFR1 might also induce apoptosis in a caspase-independent manner. The link between TNF and apoptosis shows why an abnormal production of TNF plays a fundamental role in several human diseases, especially in autoimmune diseases. The TNF receptor superfamily also includes death receptors (DRs), such as DR4 and DR5. These receptors bind to the protein TRAIL and mediate apoptosis. Apoptosis is known to be one of the primary mechanisms of targeted cancer therapy. Luminescent iridium complex-peptide hybrids (IPHs) have recently been designed, which mimic TRAIL and bind to death receptors on cancer cells, thereby inducing their apoptosis.
Developing standards-based messaging, to allow for automated data exchange Creating an exchange network, to ensure specific laboratories receive the information most pertinent to their work Improving reporting capabilities Selection and implementation of the best information management system for the laboratory's needs Strengthening the information network by sharing technical resources across public health laboratories One effort by the Informatics program is PHLIP, the Public Health Laboratory Interoperability Project. PHLIP aims to establish reliable laboratory data exchange between state public health laboratories and the CDC by fostering collaboration in IT and laboratory science.
Dysphoria and apathy (due to dopamine receptor blockade) Sedation (particularly common with asenapine, clozapine, olanzapine, quetiapine, chlorpromazine and zotepine) Headaches Dizziness Diarrhea Anxiety Extrapyramidal side effects (particularly common with first-generation antipsychotics), which include: Akathisia, an often distressing sense of inner restlessness. Dystonia, an abnormal muscle contraction Pseudoparkinsonism, symptoms that are similar to what people with Parkinson's disease experience, including tremulousness and drooling Hyperprolactinaemia (rare for those treated with clozapine, quetiapine and aripiprazole), which can cause: Galactorrhoea, the unusual secretion of breast milk. Gynaecomastia, abnormal growth of breast tissue Sexual dysfunction (in both sexes) Osteoporosis Orthostatic hypotension Weight gain (particularly prominent with clozapine, olanzapine, quetiapine and zotepine, can be counteracted by starting the drug with metformin) Antipsychotic medication-induced weight gain (AIWG) is a difficult-to-manage condition. In a meta-analysis analyzing data from 9 studies having more than 40,000 patients with AIWG, use of semaglutide was on an average was associated with 7.37kg weight loss with a good reduction in waist circumference. The occurrence of psychiatric adverse events was lower in semaglutide users.
Archives of Biochemistry and Biophysics is a biweekly peer-reviewed scientific journal that covers research in biochemistry and biophysics. It is published by Elsevier. As of 2012, the editors-in-chief were Paul Fitzpatrick (University of Texas Health Science Center at San Antonio), Helmut Sies (University of Düsseldorf), Jian-Ping Jin (Wayne State University School of Medicine), and Henry Jay Forman (University of Southern California). The journal was established in 1942 by Academic Press as the Archives of Biochemistry, obtaining its current name in 1952. It absorbed the journal Molecular Cell Biology Research Communications (formerly section B of Biochemical and Biophysical Research Communications), which was published from 1999 to 2001. An index to authors for the first 75 volumes, covering the period from 1943 to 1958, was published in October 1959.
Sources: en.wikipedia.org
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.
System suitability tests are short checks performed before or during an HPLC run to verify instrument and method performance. They often include resolution, tailing factor, theoretical plates, and injection precision. Results must meet predefined limits for sample data to be accepted.
HPLC retention time alone cannot definitively identify an unknown substance. A match with a reference standard under identical conditions provides supporting evidence. Confirmation typically requires mass spectrometry, nuclear magnetic resonance, or another orthogonal technique.
HPLC separates and quantifies compounds in a liquid sample. Detectors produce a response proportional to the amount of a compound passing through the flow cell. Identification by retention time requires comparison with a known standard.