Everything below concerns mobile phase. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Last reviewed on 2025-06-16. Where a claim depends on a specific study, the study is described rather than over-claimed.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
| Property | Value | Notes |
|---|---|---|
| Abbreviation | HPLC | Also called high-performance liquid chromatography |
| Separation mechanism | Differential partitioning | Compounds distribute between mobile and stationary phases |
| Typical column chemistry | C18 (octadecylsilane) | Used in reversed-phase separations |
| Typical detector | UV-Vis or photodiode array | Mass spectrometry is common for trace and confirmatory work |
| Typical particle size | 1.8–5 µm | Smaller particles require higher pressure and can improve speed |
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Camurus is a company focused on the development of lipid lyotropic liquid crystal structures for pharmaceutical drug delivery applications. These structures are well-defined three-dimensional formations consisting of lipophilic and hydrophilic domains that can be either interconnected or isolated depending on the environmentally induced phase conditions. The unique crystalline structures offer a unique way of encapsulating and transporting Active pharmaceutical ingredients, such as small molecules, peptides and proteins through the body. The structures also allow for the use of controlled release and prevention of degradation of fragile short half live molecules, a serious issue for amino-acid based drugs.
ADP + Pi + 2H+out ⇌ ATP + H2O + 2H+in ATP synthase lies across a cellular membrane and forms an aperture that protons can cross from areas of high concentration to areas of low concentration, imparting energy for the synthesis of ATP. This electrochemical gradient is generated by the electron transport chain and allows cells to store energy in ATP for later use. In prokaryotic cells ATP synthase lies across the plasma membrane, while in eukaryotic cells it lies across the inner mitochondrial membrane. Organisms capable of photosynthesis also have ATP synthase across the thylakoid membrane, which in plants is located in the chloroplast and in cyanobacteria is located in the cytoplasm. ATP synthase is present in all organisms studied. Eukaryotic ATP synthases are F-ATPases (which usually work as ATP synthases instead of ATPases in cellular environments) and running "in reverse" for an ATPase (ATPases catalyze the decomposition of ATP into ADP and a free phosphate ion). This article deals mainly with this type. An F-ATPase consists of two main subunits, FO and F1, which has a rotational motor mechanism allowing for ATP production.
Freeze-drying, also known as freeze-casting or ice-templating, offers an alternative to the high temperature and high-pressure requirements of supercritical drying. Additionally, freeze-drying offers more control of the solid structure development by controlling the ice crystal growth during freezing. In this method, a colloidal dispersion of the aerogel precursors is frozen, with the liquid component freezing into different morphologies depending on a variety of factors such as the precursor concentration, type of liquid, temperature of freezing, and freezing container. As this liquid freezes, the solid precursor molecules are forced into the spaces between the growing crystals. Once completely frozen, the frozen liquid is sublimed into a gas through lyophilization, which removes much of the capillary forces, as was observed in supercritical drying. Though typically classified as a "cryogel", aerogels produced through freeze-drying often experience some shrinkage and cracking while also producing a non-homogenous aerogel framework. This often leads to freeze-drying being used for the creation of aerogel powders or as a framework for composite aerogels.
In biochemistry, two biopolymers are antiparallel if they run parallel to each other but with opposite directionality (alignments). An example is the two complementary strands of a DNA double helix, which run in opposite directions alongside each other. Nucleic acid molecules have a phosphoryl (5') end and a hydroxyl (3') end. This notation follows from organic chemistry nomenclature, and can be used to define the movement of enzymes such as DNA polymerases relative to the DNA strand in a non-arbitrary manner.
The polar, uncharged amino acids serine (Ser, S), threonine (Thr, T), asparagine (Asn, N) and glutamine (Gln, Q) readily form hydrogen bonds with water and other amino acids. They do not ionize in normal conditions, a prominent exception being the catalytic serine in serine proteases. This is an example of severe perturbation, and is not characteristic of serine residues in general. Threonine has two chiral centers, not only the L (2S) chiral center at the α-carbon shared by all amino acids apart from achiral glycine, but also (3R) at the β-carbon. The full stereochemical specification is (2S,3R)-L-threonine. Because of the presence of phenolic hydroxyl group with a pKa = ~10, tyrosine is best classified as a neutral polar amino acid, but with amphipathic character that makes it less polar than classical small polar amino acid residues. Nonpolar amino acid interactions are the primary driving force behind the processes that fold proteins into their functional three dimensional structures. None of these amino acids' side chains ionize easily, and therefore do not have pKas.
Sources: en.wikipedia.org
Aerosol mass spectrometry is the application of mass spectrometry to the analysis of the composition of aerosol particles. Aerosol particles are defined as solid and liquid particles suspended in a gas (air), with size range of 3 nm to 100 μm in diameter and are produced from natural and anthropogenic sources, through a variety of different processes that include wind-blown suspension and combustion of fossil fuels and biomass. Analysis of these particles is important owing to their major impacts on global climate change, visibility, regional air pollution and human health. Aerosols are very complex in structure, can contain thousands of different chemical compounds within a single particle, and need to be analysed for both size and chemical composition, in real-time or off-line applications. Off-line mass spectrometry is performed on collected particles, while on-line mass spectrometry is performed on particles introduced in real time.
Microscale manipulation and patterning of biological materials such as proteins, cells and tissues have been used in the development of cell-based arrays, microarrays, microfabrication based tissue engineering, and artificial organs. Biological micropatterning can be used for high-throughput single cell analysis, precise control of cellular microenvironment, as well as controlled integration of cells into appropriate multi-cellular architectures to recapitulate in vivo conditions. Photolithography, microcontact printing, selective microfluidic delivery, and self-assembled monolayers are some methods used to pattern biological molecules onto surfaces. Cell micropatterning can be done using microcontact patterning of extracellular matrix proteins, cellular electrophoresis, optical tweezer arrays, dielectrophoresis, and electrochemically active surfaces.
As of 2026, there is no cure or effective treatment for CJD. Some of the symptoms, like twitching, can be managed, but otherwise treatment is palliative care. Psychiatric symptoms like anxiety and depression can be treated with sedatives and antidepressants. Myoclonic jerks can be handled with clonazepam or sodium valproate. Opiates can help with pain. Seizures are very uncommon but can nevertheless be treated with antiepileptic drugs. In 2022, results of an early-stage trial of PRN100, a monoclonal antibody against PrP, were reported: the drug appeared safe and reached the brain, but treated patients did not show clearly improved survival compared to historical controls. While not curative, this trial demonstrated the feasibility of immunotherapy for prion disease. In 2025, preclinical research demonstrated that oral, low-dose treatment with the antiretroviral medication efavirenz extended survival and slowed disease progression in a humanized mouse model of sporadic CJD (sCJD). The drug acts as an allosteric activator of the brain-specific cholesterol-metabolizing enzyme CYP46A1. This mechanism promotes brain cholesterol turnover, reduces the neurotoxic accumulation of pathological prion proteins (PrPSc), and alleviates metabolic lipid alterations in the brain.
Ansuvimab is a monoclonal antibody therapy that is infused intravenously into people with Ebola virus disease. Ansuvimab is a neutralizing antibody, meaning it binds to a protein on the surface of Ebola virus that is required to infect cells. Specifically, ansuvimab neutralizes infection by binding to a region of the Ebola virus envelope glycoprotein that, in the absence of ansuvimab, would interact with virus's cell receptor protein, Niemann-Pick C1 (NPC1). This "competition" by ansuvimab prevents Ebola virus from binding to NPC1 and "neutralizes" the virus's ability to infect the targeted cell.
The terms "active" and "passive" are simple but important terms in the world of automotive safety. "Active safety" is used to refer to technology assisting in the prevention of a crash and "passive safety" to components of the vehicle (primarily airbags, seatbelts and the physical structure of the vehicle) that help to protect occupants during a crash. Crash avoidance systems and devices help the driver — and, increasingly, help the vehicle itself — to avoid a collision. This category includes: The vehicle's headlamps, reflectors, and other lights and signals The vehicle's mirrors The vehicle's brakes, steering, and suspension systems A subset of crash avoidance is driver assistance systems, which help the driver to detect obstacles and to control the vehicle. Driver assistance systems include:
Sources: en.wikipedia.org
Acetyl phosphate (AcP), a precursor to ATP, can readily be synthesized at modest yields from thioacetate in pH 7 and 20 °C and pH 8 and 50 °C, although acetyl phosphate is less stable in warmer temperatures and alkaline conditions than in cooler and acidic to neutral conditions. It is unable to promote polymerization of ribonucleotides and amino acids and was only capable of phosphorylation of organic compounds. It was shown that it can promote aggregation and stabilization of AMP in the presence of Na+, aggregation of nucleotides could promote polymerization above 75 °C in the absence of Na+. It is possible that polymerization promoted by AcP could occur at mineral surfaces. It was shown that ADP can only be phosphorylated to ATP by AcP and other nucleoside triphosphates were not phosphorylated by AcP. This might explain why all lifeforms use ATP to drive biochemical reactions.
isoform.io is a database of AlphaFold2-generated structures of proposed splice isoforms in the human genome. It includes information from 237,275 human transcripts. It has been used to detect errors in the mRNA predictions for a handful of genes. AlphaFold has shown certain limitations. AlphaFold DB provides models of individual protein chains (monomers), rather than their biologically relevant complexes. Many protein regions are predicted with low confidence score, including the intrinsically disordered protein regions. Alphafold-2 was validated for predicting effects of point mutations on structure and free energy, with a partial success.
ABS-201 is an AI-designed monoclonal antibody against the prolactin receptor (PRLR) currently in Phase 1/2a clinical trial for the treatment of androgenic alopecia (pattern hair loss) and endometriosis. It is taken by subcutaneous injection. ABS-201 is a possible first-in-class drug with a novel mechanism of action in the potential treatment of hair loss. ABS-201 is under development by Absci. It is believed that ABS-201 works by activating dormant hair follicles and causing them to move from the telogen phase to the anagen phase. In human ex vivo scalp model studies, ABS-201 stimulated hair regrowth, prolonged anagen phase, blocked catagen phase, inhibited telogen effluvium, and blocked hair from losing color. ABS-201 has been found to produce robust hair regrowth as compared with minoxidil in mice and balding macaques. The clinical trial for ABS-201 is being overseen by prominent hair loss researcher Rodney Sinclair, one of the principal investigators in minoxidil clinical trials. The chemical structure of the drug does not yet appear to have been disclosed.
Many different inventions and ideas which may or may not have been practical about auto safety have been put forward but never made it to a production car. Such items include the driver seat in the middle (to give the person a better view) (the exception being the McLaren F1 super car) and control stick steering. Automotive safety may have become an issue almost from the beginning of mechanised road vehicle development. The second steam-powered "Fardier" (artillery tractor), created by Nicolas-Joseph Cugnot in 1771, is reported by some to have crashed into a wall during its demonstration run. However, according to Georges Ageon, the earliest mention of this occurrence dates from 1801 and it does not feature in contemporary accounts. One of the earliest recorded car-related fatalities was Mary Ward, on August 31, 1869, in Parsonstown, Ireland. In 1922, the Duesenburg Model A became the first car to have four-wheel hydraulic brakes.
Amphetamine-Dextroamphetamine is known to hamper appetite. Amphetamine-Dextroamphetamine is used to treat Attention deficit hyperactivity disorder (ADHD) and is usually under the trade name "Adderall" or "Mydayis". Amphetamine sulfate (also known as amfetamine) – US FDA-approved for the treatment of exogenous obesity under the brand name "Evekeo". Methylphenidate Cocaine Caffeine Glucomannan Leptin Lisdexamfetamine - US FDA approved for the treatment of binge-eating disorder in adults under the brand name "Vyvanse". Methamphetamine hydrochloride – USFDA-approved for the treatment of obesity (as a short-term) under the brand name "Desoxyn". Nicotine Liraglutide as brand name Saxenda Semaglutide (brand name Ozempic/Wegovy) GLP-1 agonist Tirzepatide (Brand Name Mounjaro, Zepbound) Metformin Opiates/opioids such as heroin, morphine, codeine, oxycodone, fentanyl, etc. Anti-obesity medication
Sources: en.wikipedia.org
It measures the presence and amount of one or more compounds in a liquid sample. Separation occurs in a column, and detection produces a signal proportional to concentration. Identification usually requires comparison with a known reference standard under the same conditions.
In most cases the sample is consumed or altered during analysis, though some detectors are non-destructive. Fractions can be collected after separation for further study. Repeated testing therefore requires additional sample.
Run times range from under a minute for fast methods to over an hour for complex separations. Sample preparation, equilibration, and data review add time. Throughput depends on instrument configuration and method requirements.
Validation establishes suitability for a new method, while verification confirms that a method works in a specific laboratory. Verification is often used when a validated method is adopted with existing equipment and staff. Both rely on documented acceptance criteria.