stationary phase raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2025-04-17 and is reviewed periodically as new material appears.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
| Property | Value | Notes |
|---|---|---|
| Accuracy | Recovery near 100% | Depends on acceptance criteria and matrix |
| Precision | Relative standard deviation | Often at or below 2% for replicate injections |
| Limit of detection | Signal-to-noise ratio 3:1 | Approximate and method-specific |
| Limit of quantitation | Signal-to-noise ratio 10:1 | Confirmed by precision and accuracy |
| Resolution | 1.5 or greater | Typical system suitability target |
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
The permeability of a membrane is the rate of passive diffusion of molecules through the membrane. These molecules are known as permeant molecules. Permeability depends mainly on the electric charge and polarity of the molecule and to a lesser extent the molar mass of the molecule. Due to the cell membrane's hydrophobic nature, small electrically neutral molecules pass through the membrane more easily than charged, large ones. The inability of charged molecules to pass through the cell membrane results in pH partition of substances throughout the fluid compartments of the body. Lipids, Membranes and Vesicle Trafficking – The Virtual Library of Biochemistry and Cell Biology Cell membrane protein extraction protocol Membrane homeostasis, tension regulation, mechanosensitive membrane exchange and membrane traffic 3D structures of proteins associated with plasma membrane of eukaryotic cells Lipid composition and proteins of some eukariotic membranes Prokaryotic and Eukaryotic Cells
Naturally occurring chitin and certain peptides have been recognized for their antimicrobial properties. Today, these materials are engineered into nanoparticles to produce low-cost disinfection applications. Natural peptides form nano-scale channels in the bacterial cell membranes, which causes osmotic collapse. These peptides are now synthesized to tailor the antimicrobial nanostructures with respect to size, morphology, coatings, derivatization, and other properties allowing them to be used for specific antimicrobial properties as desired. Chitosan is a polymer obtained from chitin in arthropod shells, and has been used for its antibacterial properties for a while, but even more so since the polymer has been made into nanoparticles. Chitosan proves to be effective against bacteria, viruses, and fungi, however, it is more effective against fungi and viruses than bacteria. The positively charged chitosan nanoparticles interact with the negatively charged cell membrane, which causes an increase in membrane permeability, and eventually the intracellular components leak and rupture.
Automated iterative homologation enables stepwise construction of carbon chains through repeated one-carbon extensions of boronic esters. Two reactions adapted to automation are the Matteson homologation, which inserts a methylene unit via chloromethyllithium, and chiral carbenoid homologation, which uses lithiated benzoate esters. Both methods have been implemented on robotic platforms under low-temperature, inert conditions. Using these techniques, up to six consecutive C(sp³)–C(sp³) bond-forming homologations have been performed without manual intervention, representing the highest number reported in an automated synthesis. The approach has also been applied to the synthesis of intermediates of the natural product (+)-kalkitoxin.
Sources: en.wikipedia.org
A property of DNA is its ability to re-anneal into double-stranded molecules when pH conditions are neutralized. Under neutral conditions, hydrogen bonds reform between complementary base pairs. Because the plasmid was so tightly coiled and small before the alkaline conditions were established, it can easily re-anneal. The chromosomal DNA, however, because of its lengthy strands, does not re-anneal. Once the plasmid DNA reassociates into double-stranded molecules, it dissolves into the solution. Potassium acetate reacts with the SDS detergent, magnesium ions, and calcium ions already present in the solution and forms potassium dodecyl sulfate (KDS), an insoluble white solid which precipitates out of solution. The remaining chromosomal DNA strands, denatured proteins, and added chemicals stick together and precipitate out with the KDS. The plasmid DNA, however, remains dissolved in the liquid solution. The solution is usually centrifuged to collect the insoluble precipitates into a debris pellet at the bottom of the sample tube and thereby isolate them from the supernatant.
At the present time the Department promotes various scientific fields, running the whole gamut of base branches of classical physical chemistry: thermodynamics, kinetics, electrochemistry, catalysis, sorption processes. As the subjects of research, organic compounds unite all the aforesaid research areas. Over the last years staff members of the Department of Physical Chemistry made reports at conferences in many countries of the world: Canada, Poland, Republic of South Africa, Italy, Germany, Portugal, Czech Republic, USA, Ireland, Croatia, Spain, Sweden, Japan, Brazil. The head of the Department is Professor Boris N. Solomonov, Doctor of Science in Chemistry. The Department conducts research in the following fields:
Different amino-acid sequences have different propensities for forming α-helical structure. Alanine, uncharged glutamate, leucine, charged arginine, methionine and charged lysine have especially high helix-forming propensities, whereas proline and glycine have poor helix-forming propensities. Proline either breaks or kinks a helix, both because it cannot donate an amide hydrogen bond (because it has none) and because its sidechain interferes sterically with the backbone of the preceding turn – inside a helix, which forces a bend of about 30° in the helix's axis. However, proline is often the first residue of a helix, presumably due to its structural rigidity. At the other extreme, glycine also tends to disrupt helices because its high conformational flexibility makes it entropically expensive to adopt the relatively constrained α-helical structure.
According to the fluid mosaic model of S. J. Singer and G. L. Nicolson (1972), which replaced the earlier model of Davson and Danielli, biological membranes can be considered as a two-dimensional liquid in which lipid and protein molecules diffuse more or less easily. Although the lipid bilayers that form the basis of the membranes do indeed form two-dimensional liquids by themselves, the plasma membrane also contains a large quantity of proteins, which provide more structure. Examples of such structures are protein-protein complexes, pickets and fences formed by the actin-based cytoskeleton, and potentially lipid rafts.
Sources: en.wikipedia.org
Data from high-throughput chromosome conformation capture experiments, such as Hi-C (experiment) and ChIA-PET, can provide information on the three-dimensional structure and nuclear organization of chromatin. Bioinformatic challenges in this field include partitioning the genome into domains, such as Topologically Associating Domains (TADs), that are organised together in three-dimensional space. Finding the structure of proteins is an important application of bioinformatics. The Critical Assessment of Protein Structure Prediction (CASP) is an open competition where worldwide research groups submit protein models for evaluating unknown protein models.
Beta-peptides (β-peptides) are peptides derived from β-amino acids, in which the amino group is attached to the β-carbon (i.e. the carbon two atoms away from the carboxylate group). The parent β-amino acid is β-alanine (H2NCH2CH2CO2H), a common natural substance, but most examples feature substituents in place of one or more C-H bonds. β-peptides usually do not occur in nature. β-Peptide-based antibiotics are being explored as ways of evading antibiotic resistance. Early studies in this field were published in 1996 by the group of Dieter Seebach and that of Samuel Gellman.
A property of DNA is its ability to re-anneal into double-stranded molecules when pH conditions are neutralized. Under neutral conditions, hydrogen bonds reform between complementary base pairs. Because the plasmid was so tightly coiled and small before the alkaline conditions were established, it can easily re-anneal. The chromosomal DNA, however, because of its lengthy strands, does not re-anneal. Once the plasmid DNA reassociates into double-stranded molecules, it dissolves into the solution. Potassium acetate reacts with the SDS detergent, magnesium ions, and calcium ions already present in the solution and forms potassium dodecyl sulfate (KDS), an insoluble white solid which precipitates out of solution. The remaining chromosomal DNA strands, denatured proteins, and added chemicals stick together and precipitate out with the KDS. The plasmid DNA, however, remains dissolved in the liquid solution. The solution is usually centrifuged to collect the insoluble precipitates into a debris pellet at the bottom of the sample tube and thereby isolate them from the supernatant.
Sources: en.wikipedia.org
Validation establishes suitability for a new method, while verification confirms that a method works in a specific laboratory. Verification is often used when a validated method is adopted with existing equipment and staff. Both rely on documented acceptance criteria.
Quantification usually compares detector response to a standard curve made from reference standards. The curve may be external, internal, or based on standard addition depending on matrix effects. Results are reported with units and, when required, uncertainty.
Carryover occurs when analyte from a previous injection remains in the system and appears in a later chromatogram. It can come from the injector, column, or tubing. Blank injections and needle washes help detect and reduce it.
System suitability is a set of checks that confirm the instrument and method perform within limits before sample analysis. It typically includes resolution, tailing factor, retention time, and peak area reproducibility. If a check fails, the run is invalidated until the cause is resolved.