The short version of Mobile phase fits in a sentence. The long version — which is the one that helps — is below.
This page was last updated on 2025-11-19 and is reviewed periodically as new material appears.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness of measured value to accepted reference value |
| Validation parameter | Precision | Agreement among repeated measurements under specified conditions |
| System suitability check | Resolution ≥ 1.5 | Baseline separation between critical peak pair |
| System suitability check | Tailing factor ≤ 2.0 | Common target for peak symmetry |
| Documentation | Validation report | Summarizes experiments, acceptance criteria, and conclusions |
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Arthur 'Blaine' Bowman (born 1946 in Ogden, Utah, USA) is a leading proponent of ion chromatography, who has served variously as chairman, president, chief executive officer, and director of Dionex Corporation, a manufacturer of analytical instruments. Bowman received the 2015 Pittcon Heritage Award in recognition of his contributions to the field of ion chromatography. Arthur 'Blaine' Bowman was born in 1946 in Ogden, Utah, US. Around age 10, his family moved to Southern California, where he grew up. Bowman attended Brigham Young University in Provo, Utah in the physics program. As an undergraduate, he worked in the summer as an engineer at McDonnell Douglas, testing modules for the Apollo rocket. Bowman received his B.S. in physics in 1970. Next, Bowman worked as a product engineer at Motorola's Semiconductor Products Division in Phoenix, Arizona, where he became interested in business. He attended Stanford University's school of business from 1971 to 1973, receiving his M.B.A. in 1973. He then joined McKinsey & Company as a management consultant.
Acids are fundamental reagents in treating almost all processes in modern industry. Sulfuric acid, a diprotic acid, is the most widely used acid in industry, and is also the most-produced industrial chemical in the world. It is mainly used in producing fertilizer, detergent, batteries and dyes, as well as used in processing many products such like removing impurities. According to the statistics data in 2011, the annual production of sulfuric acid was around 200 million tonnes in the world. For example, phosphate minerals react with sulfuric acid to produce phosphoric acid for the production of phosphate fertilizers, and zinc is produced by dissolving zinc oxide into sulfuric acid, purifying the solution and electrowinning. In the chemical industry, acids react in neutralization reactions to produce salts. For example, nitric acid reacts with ammonia to produce ammonium nitrate, a fertilizer. Additionally, carboxylic acids can be esterified with alcohols, to produce esters. Acids are often used to remove rust and other corrosion from metals in a process known as pickling. They may be used as an electrolyte in a wet cell battery, such as sulfuric acid in a car battery.
Amyloid is formed through the polymerization of hundreds to thousands of monomeric peptides or proteins into long fibers. Amyloid formation involves a lag phase (also called nucleation phase), an exponential phase (also called growth phase) and a plateau phase (also called saturation phase), as shown in the figure. When the quantity of fibrils is plotted versus time, a sigmoidal time course is observed reflecting the three distinct phases. In the simplest model of 'nucleated polymerization' (marked by red arrows in the figure below), individual unfolded or partially unfolded polypeptide chains (monomers) convert into a nucleus (monomer or oligomer) via a thermodynamically unfavourable process that occurs early in the lag phase. Fibrils grow subsequently from these nuclei through the addition of monomers in the exponential phase. A different model, called 'nucleated conformational conversion' and marked by blue arrows in the figure below, was introduced later on to fit some experimental observations: monomers have often been found to convert rapidly into misfolded and highly disorganized oligomers distinct from nuclei. Only later on, will these aggregates reorganise structurally into nuclei, on which other disorganised oligomers will add and reorganise through a templating or induced-fit mechanism (this 'nucleated conformational conversion' model), eventually forming fibrils.
An organic compound is a chemical whose molecules contain carbon. Carbon is abundant in the Sun, stars, comets, and in the atmospheres of most planets of the Solar System. Organic compounds are relatively common in space, formed by "factories of complex molecular synthesis" which occur in molecular clouds and circumstellar envelopes, and chemically evolve after reactions are initiated mostly by ionizing radiation. Purine and pyrimidine nucleobases including guanine, adenine, cytosine, uracil, and thymine, as well as sugars, have been found in meteorites. These could have provided the materials for DNA and RNA to form on the early Earth. The amino acid glycine was found in material ejected from comet Wild 2; it had earlier been detected in meteorites. Comets are encrusted with dark material, thought to be a tar-like organic substance formed from simple carbon compounds under ionizing radiation. A rain of material from comets could have brought such complex organic molecules to Earth. During the Late Heavy Bombardment, meteorites may have delivered up to five million tons of organic prebiotic elements to Earth per year. Currently 40,000 tons of cosmic dust falls to Earth each year.
Sources: en.wikipedia.org
Klibanski became chief of the Neuroendocrine Unit at Massachusetts General Hospital, studying hormones and neuroendocrinology with a focus on hypopituitarism and pituitary tumors. Her clinical research has also examined the effects of hypothalamic and pituitary disorders on body composition and bone density, including bone loss associated with anorexia nervosa and growth hormone deficiency. In 1997, Klibanski became the first woman from Mass General's Department of Medicine to become a professor of medicine at Harvard. She has authored more than 350 peer-reviewed papers and book chapters and has received the Endocrine Society Clinical Investigator Award and the Clinical Endocrinology Trust Medal from the Society for Endocrinology. Klibanski has served on the National Institute of Diabetes and Digestive and Kidney Diseases Board of Counselors and the editorial board of the Journal of Clinical Endocrinology and Metabolism, and is a past president of the Pituitary Society. She established the Center for Faculty Development at Massachusetts General Hospital and mentored more than fifty women, for which she received the Endocrine Society's Outstanding Mentor Award.
Five amino acids possess a charge at neutral pH. Often these side chains appear at the surfaces on proteins to enable their solubility in water, and side chains with opposite charges form important electrostatic contacts called salt bridges that maintain structures within a single protein or between interfacing proteins. Many proteins bind metal into their structures specifically, and these interactions are commonly mediated by charged side chains such as aspartate, glutamate and histidine. Under certain conditions, each ion-forming group can be charged, forming double salts. The two negatively charged amino acids at neutral pH are aspartate (Asp, D) and glutamate (Glu, E). The anionic carboxylate groups behave as Brønsted bases in most circumstances. Enzymes in very low pH environments, like the aspartic protease pepsin in mammalian stomachs, may have catalytic aspartate or glutamate residues that act as Brønsted acids.
BIA Separations was formed in 1998 by a group of scientists in Ljubljana, Slovenia to commercialize a new chromatographic resin based on monolith technology. Monolithic resin was developed independently by three different laboratories in late 1980s led by Hjertén, Švec and Tennikova. The company was one of the few Slovenian companies to receive venture capital funding at that time-Horizonte Venture Management realizing the potential of monoliths made the initial investment in the company. During that year, BIA Separations released its first commercial product marketed under the trade name of CIM (Convective Interaction Media). The new technique was named HPMC (High Performance Monolith Chromatography). During the 1999 and 2000s, the company promoted this new platform technology to the scientific and business community and registered several patents. In 2007 the company headquarters moved to Villach, Austria. In 2011 BIA Separations entered a strategic partnership with Japan Synthetic Rubber Corporation, a Japanese company producing synthetic materials. A strategic partnership agreement with Showa Denko K.K. (SDK) was signed in 2012.
Molecular biomarkers have been defined as biomarkers that can be discovered using basic and acceptable platforms such as genomics and proteomics. Many genomic and proteomics techniques are available for biomarker discovery and a few techniques that are recently being used can be found on that page. Apart from genomics and proteomics platforms biomarker assay techniques, metabolomics, lipidomics, glycomics, and secretomics are the most commonly used as techniques in identification of biomarkers. Biomarkers can be classified on their clinical applications as molecular biomarkers, cellular biomarkers or imaging biomarkers. Four of the main types of molecular biomarkers are genomic biomarkers, transcriptomic biomarkers, proteomic biomarkers and metabolic biomarkers.
Since the bacteriophage Phage Φ-X174 was sequenced in 1977, the DNA sequences of thousands of organisms have been decoded and stored in databases. This sequence information is analyzed to determine genes that encode proteins, RNA genes, regulatory sequences, structural motifs, and repetitive sequences. A comparison of genes within a species or between different species can show similarities between protein functions, or relations between species (the use of molecular systematics to construct phylogenetic trees). With the growing amount of data, it long ago became impractical to analyze DNA sequences manually. Computer programs such as BLAST are used routinely to search sequences—as of 2008, from more than 260,000 organisms, containing over 190 billion nucleotides. Before sequences can be analyzed, they are obtained from a data storage bank, such as GenBank. DNA sequencing is still a non-trivial problem as the raw data may be noisy or affected by weak signals. Algorithms have been developed for base calling for the various experimental approaches to DNA sequencing.
Sources: en.wikipedia.org
The 2014 Ebola outbreak killed more than 11,300 people. In the Democratic Republic of Congo (DRC), as of January 2020, this is the second largest outbreak with over 3,400 confirmed or probable cases, including more than 2,200 deaths. Regeneron used its VelociGene, VelocImmune, and VelociMab antibody discovery and production technologies and coordinated with the U.S. government's Biomedical Advanced Research and Development Authority (BARDA). The therapy was developed in 6 months and a Phase 1 trial in healthy humans was completed in 2015.
As a practical matter, when platinum group metals are purified through dissolution in aqua regia, gold (commonly associated with PGMs) is precipitated by treatment with iron(II) chloride. Platinum in the filtrate, as hexachloroplatinate(IV), is converted to ammonium hexachloroplatinate by the addition of ammonium chloride. This ammonium salt is extremely insoluble, and it can be filtered off. Ignition (strong heating) converts it to platinum metal: 3 [NH4]2[PtCl6] → 3 Pt + 2 N2 + 2 [NH4]Cl + 16 HCl Unprecipitated hexachloroplatinate(IV) is reduced with elemental zinc, and a similar method is suitable for small scale recovery of platinum from laboratory residues. Aqua regia reacts with tin to form tin(IV) chloride, containing tin in its highest oxidation state: 4 HCl + 2 HNO3 + Sn → SnCl4 + NO2 + NO + 3 H2O Aqua regia can react with iron pyrite to form iron(III) chloride: FeS2 + 5 HNO3 + 3 HCl → FeCl3 + 2 H2SO4 + 5 NO + 2 H2O
Clear Lake Audiotorium is a six-track promo EP by De La Soul given out to A-list DJs in 1994, the catalog number is TB 1093 (Side A, "THIS SIDE" is TB 1093 A and Side B "OTHER SIDE" is TB 1093 B). It was composed of four tracks from the group's album Buhloone Mindstate and two non-album tracks—"Sh.Fe.Mc's" featuring A Tribe Called Quest, and "Stix & Stonz" featuring The Fearless Four, Grandmaster Caz, and Prince Whipper Whip. With only 500 copies pressed (vinyl and CD), Clear Lake Audiotorium remains one of the most sought-after De La Soul releases to date. Originally pressed on clear/light green vinyl and packaged in a clear plastic sleeve, the record has since been bootlegged on black vinyl. On March 7, 2025, exactly 31 years after its original release, the EP was released officially on streaming releases, alongside a limited physical re-release.
Many affected infants also have distinctive abnormalities of the head and facial (craniofacial) area. Many of the physical features associated with the disorder are congenital. In most cases, premature closure of fibrous joints (sagittal sutures) between certain bones (parietal bones) of the skull may restrict lateral growth of the skull, causing it to appear abnormally long and narrow that is disproportionate to the body size. In addition, the forehead may be abnormally prominent and the face may be triangular shaped with a hypo plastic mid face, pointed chin. Infants with this disorder may also have abnormally flat cheeks and cheekbones, large ears, prominent mouth with widely spread lips, and or underdeveloped upper jaw bones (maxillary hypoplasia). In addition, in some cases, the teeth may be abnormally crowded together, particularly toward the front of the mouth (anterior crowding) and as a result, the upper result, the upper jaw and lower teeth may not meet properly, they might be abnormally crowded together.
Sources: en.wikipedia.org
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.
Validation follows a planned protocol that tests accuracy, precision, specificity, linearity, range, detection limits, quantitation limits, and robustness. Results are compared against predefined acceptance criteria. The validation report supports regulatory filing or routine use.
Revalidation may be needed after changes to column chemistry, mobile phase, detection, sample preparation, or instrument type. It can also follow a pattern of out-of-specification results. The scope depends on whether the change affects method performance.
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.