This is a working overview of Method validation, written for readers who want more than a one-paragraph summary but less than a textbook.
Reviewed 2025-03-22. Anything still debated is marked as such rather than presented as settled.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
| Property | Value | Notes |
|---|---|---|
| Common abbreviation | HPLC | High-performance liquid chromatography |
| Separation basis | Differential partitioning | Between liquid mobile phase and solid stationary phase |
| Common mode | Reverse phase | Nonpolar column, polar mobile phase |
| Typical detector | UV-Vis absorbance | Widely used for compounds with chromophores |
| Typical column particle size | 2–5 µm | Smaller particles can improve resolution |
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
The US Food and Drug Administration (FDA) approves anti-obesity medications as an adjunctive therapy to diet and exercise for people for whom lifestyle changes do not result in sufficient weight loss. In the United States, semaglutide (Wegovy) is approved by the FDA for chronic weight management. The FDA guidelines say that a therapy may be approved if it results in weight loss that is statistically significant greater than placebo and generally at least five percent of body weight over six months that comes predominantly from fat mass. Some other prescription weight loss medications are stimulants, which are recommended only for short-term use, and thus are of limited usefulness for patients who may need to reduce weight over months or years. As of 2022, there is no pathway for approval for drugs that reduce fat mass without 5 percent overall weight loss, even if they significantly improve metabolic health; neither is there one for drugs that help patients maintain weight loss although this can be more challenging than losing weight. As of 2022, no medication has been discovered that would equal the effectiveness of bariatric surgery for long-term weight loss and improved health outcomes.
Canada's achievements in science and technology include the creation of the modern alkaline battery, the discovery of insulin, the development of the polio vaccine, and discoveries about the interior structure of the atomic nucleus. Other major Canadian scientific contributions include the artificial cardiac pacemaker, mapping the visual cortex, the development of the electron microscope, plate tectonics, deep learning, multi-touch technology, and the identification of the first black hole, Cygnus X-1. Canada has a long history of discovery in genetics, which include stem cells, site-directed mutagenesis, T-cell receptor, and the identification of the genes that cause Fanconi anemia, cystic fibrosis, and early-onset Alzheimer's disease, among numerous other diseases. The Canadian Space Agency runs an active space program focused on deep-space, planetary, and aviation research, along with rockets and satellites. Canada launched its first satellite, Alouette 1, in 1962. It contributes to the International Space Station and is known for its robotic tools, such as multiple Canadarms. Canada has initiated many long-term projects, including the Radarsat satellite series and the Black Brant rocket series.
The cell membrane can form different types of "supramembrane" structures such as caveolae, postsynaptic densities, podosomes, invadopodia, focal adhesions, and different types of cell junction. These structures are usually responsible for cell adhesion, communication, endocytosis and exocytosis. They are composed of specific proteins, such as integrins and cadherins. They can be visualized by electron microscopy or fluorescence microscopy.
Antibody mimetics are organic compounds, like antibodies, that can specifically bind antigens. They consist of artificial peptides or proteins, or aptamer-based nucleic acid molecules with a molar mass of about 3 to 20 kDa. Antibody fragments, such as Fab and nanobodies are not considered as antibody mimetics. Common advantages over antibodies are better solubility, tissue penetration, stability towards heat and enzymes, and comparatively low production costs. Antibody mimetics have been developed and commercialized as research, diagnostic and therapeutic agents. BAU (binding antibody unit, often as BAU/mL) is a measurement unit defined by the WHO for the comparison of assays detecting the same class of immunoglobulins with the same specificity.
Sources: en.wikipedia.org
The American Society for Biochemistry and Molecular Biology (ASBMB) is a learned society that was founded on December 26, 1906, at a meeting organized by John Jacob Abel (Johns Hopkins University). The roots of the society were in the American Physiological Society, which had been formed some 20 years earlier. ASBMB is the US member of the International Union of Biochemistry and Molecular Biology. The ASBMB was originally called the American Society of Biological Chemists, before obtaining its current name in 1987. The society is based in Rockville, Maryland. ASBMB's mission is to advance the science of biochemistry and molecular biology through publication of scientific and educational journals, the organization of scientific meetings, advocacy for funding of basic research and education, support of science education at all levels, and by promoting the diversity of individuals entering the scientific workforce. The organization currently has over 12,000 members.
Aside from the 22 proteinogenic amino acids, many non-proteinogenic amino acids are known. These either are not found in proteins (for example carnitine, GABA, ornithine) or are not produced directly and in isolation by standard cellular machinery. For example, hydroxyproline is synthesized from proline, and selenomethionine is produced by metabolic modification of methionine. Non-proteinogenic amino acids that are found in proteins are formed by post-translational modification. Such modifications can also determine the localization of the protein, e.g., the addition of long hydrophobic groups can cause a protein to bind to a phospholipid membrane. Examples:
Depending on the column size, CIM monolithic columns are primarily used for the purification or analysis of large biomolecules which are being used for cancer gene therapy, treatment of viral infectious diseases and treatment of genetic diseases. Some types of molecules that can be successfully purified using CIM columns are pDNA, IgM, inter-alpha inhibitors, virus like particles, and diverse viruses; adenoviruses, bacteriophages, feline calicivirus, hepatitis A, lentivirus, influenza A and B, rabies virus, rotavirus, tomato and pepino mosaic virus. Since 2004, BIA Separations has organized and hosted the Monolith Summer School and Symposium (MSS) which takes place every 2 years. MSS was established as there were no dedicated conferences to this technology and to bring together the top international scientists and researchers in the area of monolith chromatography to share their experiences and innovative applications. BIA Separations home page Monolith Events
Proteomics permits the quantitative analysis and detection of changes to proteins or protein biomarkers. Protein biomarkers detect a variety of biological changes, such as protein-protein interactions, post-translational modifications and immunological responses. Protein biomarkers are widely used in diagnostics due to their direct involvement in cellular functions and pathways. Protein biomarkers can provide direct information about the functional state of cells and tissues, offering insights into disease mechanisms. Techniques such as mass spectrometry, immunohistochemistry, ELISA, and flow cytometry are employed to detect protein biomarkers, which can indicate protein presence and quantification. For example, in about 20% of breast cancers, the cancer cells have an overexpression of the HER2 gene, leading to more aggressive tumor growth. HER2 status can be determined using IHC and FISH. HER2-positive breast cancers are treated with targeted therapies that specifically target the HER2 protein, inhibiting the growth of cancer cells.
While genome annotation is primarily based on sequence similarity (and thus homology), other properties of sequences can be used to predict the function of genes. In fact, most gene function prediction methods focus on protein sequences as they are more informative and more feature-rich. For instance, the distribution of hydrophobic amino acids predicts transmembrane segments in proteins. However, protein function prediction can also use external information such as gene (or protein) expression data, protein structure, or protein–protein interactions. Evolutionary biology is the study of the origin and descent of species, as well as their change over time. Informatics has assisted evolutionary biologists by enabling researchers to:
Sources: en.wikipedia.org
Casokinins and lactokinins, breakdown products of casein and whey, occur naturally after ingestion of milk products, especially cultured milk. Their role in blood pressure control is uncertain. The lactotripeptides Val-Pro-Pro and Ile-Pro-Pro produced by the probiotic Lactobacillus helveticus or derived from casein have been shown to have ACE-inhibiting and antihypertensive functions. In one study, L. helveticus PR4 was isolated from Italian cheeses.
Naturally occurring chitin and certain peptides have been recognized for their antimicrobial properties. Today, these materials are engineered into nanoparticles to produce low-cost disinfection applications. Natural peptides form nano-scale channels in the bacterial cell membranes, which causes osmotic collapse. These peptides are now synthesized to tailor the antimicrobial nanostructures with respect to size, morphology, coatings, derivatization, and other properties allowing them to be used for specific antimicrobial properties as desired. Chitosan is a polymer obtained from chitin in arthropod shells, and has been used for its antibacterial properties for a while, but even more so since the polymer has been made into nanoparticles. Chitosan proves to be effective against bacteria, viruses, and fungi, however, it is more effective against fungi and viruses than bacteria. The positively charged chitosan nanoparticles interact with the negatively charged cell membrane, which causes an increase in membrane permeability, and eventually the intracellular components leak and rupture.
Amino acids are organic compounds that contain both amino and carboxylic acid functional groups. Although over 500 amino acids exist in nature, by far the most important are the 22 α-amino acids incorporated into proteins. Only these 22 appear in the genetic code of life. Amino acids can be classified according to the locations of the core structural functional groups (alpha- (α-), beta- (β-), gamma- (γ-) amino acids, etc.); other categories relate to polarity, ionization, and side-chain group type (aliphatic, acyclic, aromatic, polar, etc.). In the form of proteins, amino-acid residues form the second-largest component (water being the largest) of human muscles and other tissues. Beyond their role as residues in proteins, amino acids participate in a number of processes such as neurotransmitter transport and biosynthesis. It is thought that they played a key role in enabling life on Earth and its emergence. Amino acids are formally named by the IUPAC-IUBMB Joint Commission on Biochemical Nomenclature in terms of the fictitious "neutral" structure shown in the illustration. For example, the systematic name of alanine is 2-aminopropanoic acid, based on the formula CH3−CH(NH2)−COOH. The Commission justified this approach as follows:
FO is a water insoluble protein with eight subunits and a transmembrane ring. The ring has a tetrameric shape with a helix-loop-helix protein that goes through conformational changes when protonated and deprotonated, pushing neighboring subunits to rotate, causing the spinning of FO which then also affects conformation of F1, resulting in switching of states of alpha and beta subunits. The FO region of ATP synthase is a proton pore that is embedded in the mitochondrial membrane. It consists of three main subunits, a, b, and c. Six c subunits make up the rotor ring, and subunit b makes up a stalk connecting to F1 OSCP that prevents the αβ hexamer from rotating. Subunit a connects b to the c ring. Humans have six additional subunits, d, e, f, g, F6, and 8 (or A6L). This part of the enzyme is located in the mitochondrial inner membrane and couples proton translocation to the rotation that causes ATP synthesis in the F1 region. In eukaryotes, mitochondrial FO forms membrane-bending dimers. These dimers self-arrange into long rows at the end of the cristae, possibly the first step of cristae formation. An atomic model for the dimeric yeast FO region was determined by cryo-EM at an overall resolution of 3.6 Å.
Sources: en.wikipedia.org
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.
Retention time is the interval between sample injection and the detector response for a given compound. It depends on the compound's interactions with the stationary and mobile phases under set conditions. Matching a retention time to a standard supports tentative identification but is not always unique.
HPLC alone can separate unknown compounds and provide retention times, but it often cannot identify them with certainty. Coupling HPLC to mass spectrometry gives mass information that improves identification. Confirmation usually requires comparison with reference standards or complementary techniques.
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.