mobile phase comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Last reviewed on 2025-06-22. Where a claim depends on a specific study, the study is described rather than over-claimed.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Nonpolar stationary phase with polar mobile phase |
| Typical column particle size | 3–5 µm | Smaller particles improve resolution but raise pressure |
| Typical flow rate | 0.5–2.0 mL/min | Depends on column dimensions and pressure limits |
| Common detection | UV-Vis absorbance | Requires analytes with chromophores |
| Typical run time | 5–30 min | Varies with method, gradient, and sample complexity |
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
The composition and rate of CSF generation are influenced by hormones and the content and pressure of blood and CSF. For example, when CSF pressure is higher, there is less of a pressure difference between the capillary blood in choroid plexuses and CSF, decreasing the rate at which fluids move into the choroid plexus and CSF generation. The autonomic nervous system influences choroid plexus CSF secretion, with activation of the sympathetic nervous system decreasing secretion and the parasympathetic nervous system increasing it. Changes in the pH of the blood can affect the activity of carbonic anhydrase, and some drugs (such as furosemide, acting on the Na-K-Cl cotransporter) have the potential to impact membrane channels.
The total nitrogen content of organic matter is mainly formed by the amino groups in proteins. The total Kjeldahl nitrogen (TKN) is a measure of nitrogen widely used in the analysis of (waste) water, soil, food, feed and organic matter in general. As the name suggests, the Kjeldahl method is applied. More sensitive methods are available. Media related to Amino acids at Wikimedia Commons
As the salt of a weak base (ammonium) and a weak acid (acetic acid), is often used to create a buffer solution. Ammonium acetate is volatile at low pressures. Because of this, it has been used to replace cell buffers that contain non-volatile salts in preparing samples for mass spectrometry. It is also popular as a buffer for mobile phases for HPLC with ELSD and CAD-based detection for this reason. Other volatile salts that have been used for this include ammonium formate. When dissolving ammonium acetate in pure water, the resulting solution typically has a pH of 7, because the equal amounts of acetate and ammonium neutralize each other. However, ammonium acetate is a dual component buffer system, which buffers around pH 4.75 ± 1 (acetate) and pH 9.25 ± 1 (ammonium), but it has no significant buffer capacity at pH 7, contrary to common misconception.
Sources: en.wikipedia.org
Individual transmembrane adenylyl cyclase isoforms have been linked to numerous physiological functions. Soluble adenylyl cyclase (sAC, AC10) has a critical role in sperm motility. Adenylyl cyclase has been implicated in memory formation, functioning as a coincidence detector. AC-IV was first reported in the bacterium Aeromonas hydrophila, and the structure of the AC-IV from Yersinia pestis has been reported. These are the smallest of the AC enzyme classes; the AC-IV (CyaB) from Yersinia is a dimer of 19 kDa subunits with no known regulatory components (PDB: 2FJT). AC-IV forms a superfamily with mammalian thiamine-triphosphatase called CYTH (CyaB, thiamine triphosphatase). These forms of AC have been reported in specific bacteria (Prevotella ruminicola O68902 and Rhizobium etli Q8KY20, respectively) and have not been extensively characterized. There are a few extra members (~400 in Pfam) known to be in class VI. Class VI enzymes possess a catalytic core similar to the one in Class III.
Formation of the Quinonoid Intermediate PLP acts as an 'electron sink' absorbing delocalized electron density during the reaction intermediates (countering the excess electron density on the deprotonated a-carbon). PLP facilitates the enzyme activity, increasing the acidity of the alpha carbon by stabilizing the conjugate base. The PLP-stabilized carbanion intermediate formed is the quinonoid intermediate. Tyrosine and PLP stabilized 3C-Ring formation PLP and Tyrosine stabilize negative charges during deprotonation. Tyrosine attacks the sulfur bound carbon, allowing S(CH3)(Ado) to leave, and during ring formation, Tyrosine leaves. Note inhibitors AVG and AMA bind PLP to form a ketimine and oxime respectively (whose reverse reactions are much less favorable) and prevent the ACC synthase catalyzed reaction with SAM.
Arrestins are elongated molecules, in which several intra-molecular interactions hold the relative orientation of the two domains. Unstimulated cell arrestins are localized in the cytoplasm in a basal inactive conformation. Active phosphorylated GPCRs recruit arrestin to the plasma membrane. Receptor binding induces a global conformational change that involves the movement of the two arrestin domains and the release of its C-terminal tail that contains clathrin and AP2 binding sites. Increased accessibility of these sites in receptor-bound arrestin targets the arrestin-receptor complex to the coated pit. Arrestins also bind microtubules (part of the cellular skeleton), where they assume yet another conformation, different from both free and receptor-bound form. Microtubule-bound arrestins recruit certain proteins to the cytoskeleton, which affects their activity and/or redirects it to microtubule-associated proteins. Arrestins shuttle between cell nucleus and cytoplasm. Their nuclear functions are not fully understood, but it was shown that all four mammalian arrestin subtypes remove some of their partners, such as protein kinase JNK3 or the ubiquitin ligase Mdm2, from the nucleus. Arrestins also modify gene expression by enhancing transcription of certain genes.
Corin converts the atrial natriuretic peptide (ANP) precursor, pro-ANP, to mature ANP, a cardiac hormone that regulates salt-water balance and blood pressure. In mice, corin deficiency prevents pro-ANP processing and causes salt-sensitive hypertension. Corin may also function as a pro-brain-type natriuretic peptide convertase. Corin-mediated ANP production in the pregnant uterus promotes spiral artery remodeling and trophoblast invasion. CORIN mutations have been reported in patients with preeclampsia. In mice, corin functions in the dermal papilla to regulate coat color in an Agouti-dependent pathway.
Sources: en.wikipedia.org
The word "aptamer" is a neologism coined by Andrew D. Ellington and Jack Szostak in their first publication on the topic. They did not provide a precise definition, stating "We have termed these individual RNA sequences 'aptamers', from the Latin aptus, to fit." The word itself, however, derives from the Greek word ἅπτω, to connect or fit (as used by Homer (c. 8th century BC)) and μέρος, a component of something larger. A typical aptamer is a synthetically generated ligand exploiting the combinatorial diversity of DNA, RNA, XNA, or peptide to achieve strong, specific binding for a particular target molecule or family of target molecules. Aptamers are occasionally classified as "chemical antibodies" or "antibody mimics". However, most aptamers are small, with a molecular weight of 6-30 kDa, in contrast to the 150 kDa size of antibodies, and contain one binding site rather than the two matching antigen binding regions of a typical antibody.
These cyclic dipeptides incorporate both donor and acceptor groups for hydrogen bonding. They are conformationally constrained nearly planar scaffolds. Diversity can be introduced at up to six positions and stereochemistry controlled at up to four positions. They are stable to proteolysis. These characteristics underpin theis biologically activity and utility in medicinal chemistry. As a consequence of their predominant biosynthetic origin from L-α-amino acids most naturally occurring 2,5-DKPs are cis configured as the cyclo(L-Xaa-L-Yaa) isomers. 2,5-DKPs epimerize under basic, acidic and thermal conditions. The composition of the cis and trans isomers in the equilibrium state varies widely depending on the bulk of the side chains, if a ring (e.g. proline) is present, or if the nitrogen atoms are alkylated . Although epimerization was historically an issue in the synthesis of 2,5-DKPs, several mild methods have been developed recently that avoid epimerization.
Vaginal gels are forms of medication that are water-based. They are applied using a plastic applicator to distribute the gel throughout the length of the vaginal canal. These gels tend to have release kinetics that are fast acting, which makes them useful for treatment of irritations. Antibiotics are often distributed in the form of a gel for treatment of common infections, including sexually transmitted infections (STIs). The gels also have the benefit of being lubricating, which grants additional relief to symptoms of dryness and itching that is common with vaginal infections. Gels that are in the form of liposomal structure have been shown to retain substances for extensive periods of time, making them useful for slow release of drugs administered through the cervical drug delivery route
Sources: en.wikipedia.org
It separates components in a liquid sample and measures their amounts using a detector. Results can indicate concentration, purity, or identity based on retention time and detector response. The technique works for mixtures that can be dissolved and filtered.
It offers high resolution, reproducibility, and compatibility with many sample types. A single run can separate and quantify multiple analytes. It is common in pharmaceutical, food, environmental, and industrial laboratories.
Samples must be soluble in a suitable mobile phase and free of particles that can block the column. Detector response depends on analyte structure, so some compounds need derivatization or alternative detection. Complex matrices may require extensive sample preparation.
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.