Everything below concerns System suitability. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Updated 2025-05-15. Numbers and descriptions here follow the published literature rather than marketing material.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
| Parameter | Typical acceptance criterion | Notes |
|---|---|---|
| Resolution | ≥ 1.5 | Baseline separation of adjacent peaks |
| Tailing factor | ≤ 2.0 | Peak symmetry measure |
| Theoretical plates | > 2000 | Column efficiency indicator |
| Injection repeatability | ≤ 2% RSD | Relative standard deviation for replicate injections |
| Linearity | r² ≥ 0.995 | Calibration curve over the working range |
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
isoform.io is a database of AlphaFold2-generated structures of proposed splice isoforms in the human genome. It includes information from 237,275 human transcripts. It has been used to detect errors in the mRNA predictions for a handful of genes. AlphaFold has shown certain limitations. AlphaFold DB provides models of individual protein chains (monomers), rather than their biologically relevant complexes. Many protein regions are predicted with low confidence score, including the intrinsically disordered protein regions. Alphafold-2 was validated for predicting effects of point mutations on structure and free energy, with a partial success.
Andexanet alfa is a biologic agent, a recombinant modified version of human activated factor X (FXa). Andexanet alfa differs from native FXa due to the removal of a 34 residue fragment that contains the Gla domain. This modification reduces andexanet alfa's anticoagulant potential. Additionally, a serine to alanine (S419A) mutation in the active site eliminates its activity as a prothrombin to thrombin catalyst, but still allows the molecule to bind to FXa inhibitors. FXa inhibitors bind to andexanet alfa with the same affinity as to natural FXa. As a consequence, in the presence of andexanet alfa, natural FXa is partially freed, which can lead to effective hemostasis. In other words, it acts as a decoy receptor. Andexanet alfa reverses effect of all anticoagulants that act directly through FXa or by binding antithrombin III. The drug is not effective against factor IIa inhibitor dabigatran. Its activity is measured using the anti-Xa test, which is utilized to determine the amount of available factor Xa for coagulation
The use of high-resolution ion-mobility mass spectrometry (IMS-MS) on HPLC-purified alpha-synuclein in vitro has shown alpha-synuclein to be autoproteolytic (self-proteolytic), generating a variety of small molecular weight fragments upon incubation. The 14.46 kDa protein was found to generate numerous smaller fragments, including 12.16 kDa (amino acids 14–133) and 10.44 kDa (40–140) fragments formed through C- and N-terminal truncation and a 7.27 kDa C-terminal fragment (72–140). The 7.27 kDa fragment, which contains the majority of the NAC region, aggregated considerably faster than full-length alpha-synuclein. It is possible that these autoproteolytic products play a role as intermediates or cofactors in the aggregation of alpha-synuclein in vivo.
Abelacimab (MAA868), is a fully human monoclonal antibody for the treatment of thrombosis, under development by Anthos Therapeutics. It is anti-factor XI antibody. The hope behind its development is that factor XI plays a bigger role in thrombosis (via the intrinsic/contact activation pathway) than hemostasis, so targeting it might reduce clotting risks without a corresponding increase in bleeding. It has, indeed, shown overwhelming reduction in bleeding as compared to a direct oral anticoagulant (rivaroxaban) in patients with atrial fibrillation and a moderate-to-high risk of stroke. Data is insufficient for drawing a conclusion on whether it increases or decreases stroke events as compared to rivaroxaban. Antibody Monoclonal antibody Immunology
Sources: en.wikipedia.org
An antibody–drug conjugate consists of three components: Antibody - targets the cancer cell surface and may also elicit a therapeutic response. Payload - elicits the desired therapeutic response. Linker - attaches the payload to the antibody and should be stable in circulation only releasing the payload at the desired target. Multiple approaches to conjugation have been developed for attachment to the antibody and reviewed. DAR is the drug to antibody ratio and indicates the level of loading of the payload on the ADC.
UniProt is an online repository of protein sequence and annotation data, distributed in UniProt Knowledgebase (UniProt KB), UniProt Reference Clusters (UniRef) and UniProt Archive (UniParc) databases. Originally conceived as the individual ventures of EMBL-EBI, Swiss Institute of Bioinformatics (SIB) (together maintaining Swiss-Prot and TrEMBL) and Protein Information Resource (PIR) (housing Protein Sequence Database), the increase in the global protein data generation led to their collaboration in the creation of UniProt in 2002. The protein entries stored in UniProt are cataloged by a unique UniProt identifier. The annotation data collected for the each entry are organized in logical sections (e.g. protein function, structure, expression, sequence or relevant publications), allowing a coordinated overview about the protein of interest. Links to external databases and original sources of data are also provided. In addition to standard search by the protein name/identifier, UniProt webpage houses tools for BLAST searching, sequence alignment or searching for proteins containing specific peptides.
Group specificity occurs when an enzyme will only react with molecules that have specific functional groups, such as aromatic structures, phosphate groups, and methyls. One example is pepsin, an enzyme that is crucial in digestion of foods ingested in our diet, that hydrolyzes peptide bonds in between hydrophobic amino acids, with recognition for aromatic side chains such as phenylalanine, tryptophan, and tyrosine. Another example is hexokinase, an enzyme involved in glycolysis that phosphorylates glucose to produce glucose-6-phosphate. This enzyme exhibits group specificity by allowing multiple hexoses (6 carbon sugars) as its substrate. Glucose is one of the most important substrates in metabolic pathways involving hexokinase due to its role in glycolysis, but is not the only substrate that hexokinase can catalyze a reaction with.
Arrestins (abbreviated Arr) are a small family of proteins important for regulating signal transduction at G protein-coupled receptors. Arrestins were first discovered in the late '80s as a part of a conserved two-step mechanism for regulating the activity of G protein-coupled receptors (GPCRs) in the visual rhodopsin system by Hermann Kühn, Scott Hall, and Ursula Wilden and in the β-adrenergic system by Martin J. Lohse and co-workers.
The iron-containing co-factor is found tightly associated with the protein. It can be released upon denaturation with 2-mercaptoethanol or guanidine hydrochloride. Expression of the Hmd gene in E. coli without the co-factor results in an inactive holoenzyme. However, hydrogenase activity can be rescued by the addition of the iron-containing cofactor taken from denatured active enzyme. As mentioned, irradiation of the cofactor with UV light results in the loss of CO and Fe. In addition the 542 Da compound can be further degraded by a phosphodiesterase (which specifically cleaves phosphate bonds). Hydrolysis of the phosphate bonds generates the ribonucleotide guanosine monophosphate and a modified 2-pyridone. On the basis of spectroscopic characterization, Shima et al. have proposed a structure for this organic cofactor (minus the iron atom and CO molecules) as shown:
Sources: en.wikipedia.org
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.
System suitability tests are short checks performed before or during an HPLC run to verify instrument and method performance. They often include resolution, tailing factor, theoretical plates, and injection precision. Results must meet predefined limits for sample data to be accepted.
HPLC retention time alone cannot definitively identify an unknown substance. A match with a reference standard under identical conditions provides supporting evidence. Confirmation typically requires mass spectrometry, nuclear magnetic resonance, or another orthogonal technique.
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.